Australian Made and Owned

This Strut Spacers 20mm Lift Suitable For Ford Ranger PX-PXII-PXIII, Toyota Prado 90, Holden Colorado RG and Colorado 7 RG.

These spacers are simply bolted to the top of the strut to provide approximately 20mm of lift.

You remove the coil from the strut and the spacer fits between the coil spring and the strut top using the supplied bolts.

You will need a coil compressor to remove the coils safely.

Superior Engineering has designed these as a cheap alternative to correct sag after fitting a bull bar, Dual batteries or other heavy accessories.

Laser-cut from 10mm plate steel for precise fit and zinc coated.

Although they are 10mm thick they will lift the front end up by 20mm over the axles.

Supplied with:

  • 2 x 10mm strut spacers
  • 6 x M10x1.25 x 40mm button head bolts
  • 6 x M10 Nylocks
  • 6 x M10 Flat washers

SOLD AS A KIT.

Note: It is only recommended to use strut spacers on standard length struts, if you use longer struts ( aftermarket) then you must check down travel, make sure the cv's do not bind and there are no fouling issues with steering components and no steering components move past there maximum working angles.

Disclaimer
Genuine/Non Genuine – Advertised parts are not genuine (unless specifically stated) and manufacturer references are for application purposes only. Only items that are specifically noted as Genuine OEM can be presumed as genuine parts.

Superior Engineering is not sponsored, approved, affiliated or otherwise associated with any genuine or original parts manufacturer, distributor or dealer.


Identification and Guidance Only – Photos are for identification purposes only and may be of either genuine or non-genuine parts.
All manufacturers names, symbols and descriptions on this website are used for reference purposes only, and it is not implied that any units or parts listed is the product of these manufacturers.

Original Equipment Manufacturer "OEM" part/reference numbers are listed for information/reference purposes only. Trademarks identifying these parts are those of each OEM and are the property of their owners and are not used, or authorized for use, by Superior Engineering. Cross-referenced parts from the Original Equipment Manufacturer "OEM" are listed for information purposes only.

Superior Engineering has no associations and/or claims to be associated with OEM Vehicle Manufacturers and their Companies worldwide. Any implied associations are purely coincidental and are not inferred. Superior Engineering is a supplier of fully interchangeable non-genuine spare parts (alternatives) for equipment produced by manufacturers using in accordance with law OEM Vehicle Manufacturers and their products, i.e. suspension parts, steering components, manufactured items, vehicle accessories etc. Alternative spare parts produced by Superior Engineering are manufactured according own technological documentation developed with the use of reverse engineering.

FAQ / Extra Info
Vehicle Information
Lift Height0-2 inch
Spacer Height20mm
SKU SE-24653
Barcode # OEBC523692
Brand Superior Engineering
Shipping Weight 1.3800kg
Shipping Width 0.150m
Shipping Height 0.050m
Shipping Length 0.150m

Superior Strut Spacers 20mm Lift To Suit Ranger/Toyota Prado 90/Holden Colorado (Kit)

SKU: SE-24653
Sale price
$103.00
PayPal Checkout
4 payments of $25.75

afterpay More info.

Make 4 payments of $25.75 over 8 weeks and get it now!

zipMoney
From $10 / week
Afterpay
4 payments of $25.75
Superior Strut Spacers 20mm Lift Suitable To Suit To Suitd Ranger/Toyota Prado 90/Holden Colorado (Kit)

Calculate Shipping

Australian Made and Owned

This Strut Spacers 20mm Lift Suitable For Ford Ranger PX-PXII-PXIII, Toyota Prado 90, Holden Colorado RG and Colorado 7 RG.

These spacers are simply bolted to the top of the strut to provide approximately 20mm of lift.

You remove the coil from the strut and the spacer fits between the coil spring and the strut top using the supplied bolts.

You will need a coil compressor to remove the coils safely.

Superior Engineering has designed these as a cheap alternative to correct sag after fitting a bull bar, Dual batteries or other heavy accessories.

Laser-cut from 10mm plate steel for precise fit and zinc coated.

Although they are 10mm thick they will lift the front end up by 20mm over the axles.

Supplied with:

  • 2 x 10mm strut spacers
  • 6 x M10x1.25 x 40mm button head bolts
  • 6 x M10 Nylocks
  • 6 x M10 Flat washers

SOLD AS A KIT.

Note: It is only recommended to use strut spacers on standard length struts, if you use longer struts ( aftermarket) then you must check down travel, make sure the cv's do not bind and there are no fouling issues with steering components and no steering components move past there maximum working angles.

Disclaimer
Genuine/Non Genuine – Advertised parts are not genuine (unless specifically stated) and manufacturer references are for application purposes only. Only items that are specifically noted as Genuine OEM can be presumed as genuine parts.

Superior Engineering is not sponsored, approved, affiliated or otherwise associated with any genuine or original parts manufacturer, distributor or dealer.


Identification and Guidance Only – Photos are for identification purposes only and may be of either genuine or non-genuine parts.
All manufacturers names, symbols and descriptions on this website are used for reference purposes only, and it is not implied that any units or parts listed is the product of these manufacturers.

Original Equipment Manufacturer "OEM" part/reference numbers are listed for information/reference purposes only. Trademarks identifying these parts are those of each OEM and are the property of their owners and are not used, or authorized for use, by Superior Engineering. Cross-referenced parts from the Original Equipment Manufacturer "OEM" are listed for information purposes only.

Superior Engineering has no associations and/or claims to be associated with OEM Vehicle Manufacturers and their Companies worldwide. Any implied associations are purely coincidental and are not inferred. Superior Engineering is a supplier of fully interchangeable non-genuine spare parts (alternatives) for equipment produced by manufacturers using in accordance with law OEM Vehicle Manufacturers and their products, i.e. suspension parts, steering components, manufactured items, vehicle accessories etc. Alternative spare parts produced by Superior Engineering are manufactured according own technological documentation developed with the use of reverse engineering.

FAQ / Extra Info
Vehicle Information
Lift Height0-2 inch
Spacer Height20mm
SKU SE-24653
Barcode # OEBC523692
Brand Superior Engineering
Shipping Weight 1.3800kg
Shipping Width 0.150m
Shipping Height 0.050m
Shipping Length 0.150m